Elite Garage Door Logo

Garage door springs replacement cost (2024 guide)

Garage Door Spring Replacement Aurora

Garage door torsion springs are one of the most vital parts of a garage door. They are used to provide the necessary tension to keep the door open. If you have a broken spring, you must replace it as soon as possible. Using a broken spring is unsafe because it can snap and cause injuries.

There are many reasons why torsion springs might break. The most common is that it was not installed properly when it was put in place or worn down after years of use.

Introduction: Why You Need a New Garage Door Spring

Garage door springs are an integral part of your garage door. They are responsible for lifting the door up and down. The tension on the spring should be adjusted, so it can lift the door easily. However, if there is too much tension in the spring, it will be difficult for the door to open and close. If you have noticed that your garage door has been getting harder to open or close, this may be a sign that you need to replace the garage door springs.

How to Identify an Overstretched or Damaged Garage Door Springs

Garage door springs are one of the most important parts of your garage door. They provide the tension that opens and closes your garage door. If you have a spring problem, it can lead to major problems with your garage door.

The following are some signs to identify if you have a garage door springs problem:

-If your door is difficult to open or close, this could be an indication of a damaged spring or worn-out spring.

-If one side of the garage door is higher than the other, this could indicate a damaged or worn-out spring.

-If you notice that there is a loud noise when opening and closing the garage door, this could be an indication of a damaged spring or worn-out spring.

-If there is no tension in the opener chain when opening and closing the garage door, this could indicate a damaged spring or worn-out springs.

How To Inspect the Condition of Your Springs Before Replacing Them

Garage door springs are a critical component of your garage door. They are the tensioners that keep the door raised and open. Over time, they will start to wear out and eventually break.

When springs break, they can cause serious injury or even death if you are under the door when it falls. You should always inspect your springs for signs of wear before you replace them.

How to Retention Garage Door Spring and What Happens When You Don’t

The springs are designed with a specific tension in mind. Over time, the springs will lose their tension, and the door will no longer be able to open or close properly. This can lead to potential safety hazards, such as the door coming off its tracks or becoming jammed in place.

If your garage door is not closing or opening correctly, it may be time to retention the garage door springs.

The first step is identifying which type of spring system your garage door has, so you know what tools you’ll need for the job. A screwdriver and a hammer will be required to complete this task. An adjustable or socket wrench can also be used if you prefer.

Finding a torque wrench is unnecessary if your door has torsion springs. Torsion springs are typically tightened with the hand crank on the outside of the garage door opener unit.  If you have extension springs, however, a torque wrench is needed for them to function properly throughout their lifetime.

To retention garage door springs, first, locate the spring that is set to open your garage door. Most systems are located at the top of each side of the garage door. If you’re unsure which one it is, use your hand to feel the tension in the spring while it’s in its unfastened position.

Once you’ve found this spring, unscrew a nut on its outside bracket with a standard screwdriver and hammer. Once this nut has been removed from around its bracket, take a screwdriver and place it in the hole that’s now exposed.

You can then use a torque wrench to tighten the nut back down securely around its bracket with the hand crank on your garage door opener unit.

The spring is a critical part of any garage door. It has to be strong enough to support the weight of the door, and it also needs to be taut enough to move up and down easily.

If you don’t retention your springs regularly, you will experience problems with your garage door. The spring will lose its strength and become less effective, making it difficult for the door to open or close properly. This can lead to more issues in the future, such as broken springs or cables.

How To Replace Your Broken Springs And Save Yourself From Repairs Cost!

The cost for a spring replacement can vary depending on the type of opener you have and what type of springs you need.

An average homeowner can typically replace a broken spring with minimal tools. The process is not difficult, but it requires patience and time.

If you are not confident in replacing the garage door springs, then it may be best to contact a professional for assistance.

The Cost of Garage Door Springs and What You Should Know

The cost of garage door springs will depend on a few things, such as whether  you need a custom-made spring or if you can find a spring that is compatible with your make and model of garage door opener.

You should also consider what material your spring is made of. Steel springs might be best for you if you are looking for an affordable option because they are inexpensive but still provide plenty of strength when lifting heavy doors.

How Much Does it Cost To Repair A Broken Garage Door Spring?

The cost of replacing a broken garage door spring can vary depending on the type of garage door and the quality of the springs.

The average cost to replace a broken garage door spring is about $200 for a basic, off-the-shelf spring set. If you need to buy an additional set, it will cost you about $160.

garage door springs

DIY vs. professional torsion garage door springs replacement

It is possible to replace a car door’s spring components in certain situations, especially if it uses garage door extension springs. You will need two cylinder springs, wrenches, stepladders, and a sanitary scale. You’ll determine the door height and weight by releasing the locket and disconnecting the safety cable. Please disconnect your motor before working. It is generally safer to have torsion springs technicians. These extreme stresses are dangerous, and their removal is more difficult than with extension springs. Spring replacement is less expensive, typically about $50–150.

The Difference Between Extension and garage door torsion springs

The garage door extension springs are under the greatest strain when stretched. Torsion springs are under the most tension compared to bed springs. Check your garage doors for extension springs and torsion springs. A parallel extension spring supports the garage door weight. The extension springs typically exist in old garage doors. These are slightly unsafe because the garage door springs may fall from the pulley and cause damage. Torsion springs are harder to detect as they are wrapped around a torsion tube normally mounted directly above the garage entrance.

Best Practices for Safely Replacing Your Old garage door springs

Garage doors are a necessity in the modern world. They provide a barrier between the outside world and your home and serve as a gatekeeper to your property. If you are experiencing issues with your garage door, you may be wondering what to do next. You may also wonder how to fix a broken torsion spring in a double garage door.

The best practice for safely replacing your old garage door spring is to call professionals specializing in this work. Garage door specialists will have the knowledge and experience necessary to ensure your garage door is safe and secure.

aurora garage door spring experts

Conclusion: The Benefits of Knowing Your Options in Replacing Your Old garage door springs

In conclusion, knowing your options for replacing old springs will help you save time and money.

Garage doors may last as many as 15 years, but even high-performance springs will eventually rust and erode. Fortunately, spring replacement does not cost much to replace. You can replace the springs yourself unless it is used in your door extension springs, but using a torsion spring is incredibly dangerous. In general, it is better to hire a garage door installation company. Get quotes today from garage door specialists near you.

You can buy replacement springs online or from hardware stores or manufacturers.

It’s not hard at all if you take measurements to know what springs are needed before you start. You can buy Torsion Springs online or at several Hardware Stores. Spring manufacturers or garage door professionals may be a more reliable alternative. They can likely supply the garage door spring you are looking for and help answer questions about the project.

aurora garage door parts

DIYers should proceed with care and caution.

Spring replacement for doors is usually in the two-category of safety – depending on the type of springs. However, replacing a garage door spring can be accomplished on your own, but without any experience as a DIYer, torsion springs are best left to experts.

Garage door parts of a Garage Door Spring System and What they do

Garage door springs are the most important garage door parts of a garage door system. They keep the door from falling and provide tension to help it open and close.

The tension on the springs is what keeps the door up and closed. When it’s time for someone to open or close the door, they push or pull on a spring-loaded trolley connected to the opener. This trolley lifts or lowers one end of the spring, so it can either be tightened or loosened.

Spring systems have four parts: two torsion springs, two trolleys, and a track opener bracket. Springs are made of coils wound together in an “S” shape with hooks at each end that attach to each trolley. The track opener center bracket is a metal bar with holes drilled in it that sits between two tracks on either side of a garage opening and attaches to both springs at their hooks.

Eight Steps for replacing garage door springs

Springs are important parts of a garage door. They help the door to open and close smoothly. If a spring breaks or wears out, it can be replaced with a new one.

1) Locate the broken garage door springs

2) Purchase new springs that are the same size as the old springs

3) Remove any rust or debris from the mounting plates and track where the springs are installed

4) Measure and cut new springs to match the length of old springs

5) Install new springs in place of old ones

6) Check for proper operation of the garage door

7) Replace any damaged sections on tracks or other parts that may have come loose during the installation process

8) Clean up after installation is completed

Average garage door parts Cost

The average cost of garage door springs and parts can range anywhere from $80-200 depending on what type you need, where you purchase them, and whether they are installed by professionals. If you’re looking to stay on budget, shopping around for your springs is best to find the best deal possible while still getting quality products.

Garage Door Springs Prices With Additional Repairs

Garage door springs repair are performed either by tuning or adjusting the tension. The springs cannot be repaired. During installation, upgrading your Garage Door System and performing other repairs can become necessary.

Door track adjustment may require adjustment of doorway tracks, or garage door opening may be cleaned. Sometimes the company offers bundled services to get more savings in the garage door industry. Contact a garage door repair expert in your area today.

Garage door springs cost by type of spring

The commonest spring on a garage door can be a torsion or extension spring. Extension springs are less costly but do not last as long—typically 5—7 years. Torsion springs can last 10 to 15 years, but the costs will be higher. The most common garage door springs require replacement often. Additional expenses are included for the springs in this package.

Garage Door Springs Cost by Type of Door

Residential structures typically use a single style of garage door: tilted and roll-up. A tilt-over door typically has an extension spring and thus will have fewer costs. Rolling doors usually have two springs for traction.

Overhead Door Torsion Spring Replacement Cost

Elite Garage Doors in Aurora, Colorado specializes in torsion spring replacement for overhead doors. We understand how important it is to keep these springs running smoothly and safely so that your garage door can function correctly. Replacing these springs can range from three hundred fifty to five hundred dollars depending on the size, materials, and the amount of labor required. Elite Garage Doors will always strive to provide our customers with quality services at an affordable cost. Contact us today for a free quote to make sure your overhead door is fitted with properly functioning torsion springs!

Signs You Need To Replace Your Garage Door Springs

Garage doors make a loud banging sound when the spring snaps, so the driver knows if it broke. Another sign your old spring needs replacement.

Spring replacement vs. whole garage door replacement

Spring replacements can fix the door in an emergency. Nevertheless, it may take a long time if you need to repair all parts on a door unless the door itself has been damaged. Some people replace single panels in sections of garage doors, but it is probably more economical to replace the entire unit if multiple panels have been damaged. You can even upgrade the garage door or system.

How to save on Garage Door Springs Costs?

Although installing garage doors isn’t as expensive as other house improvements, you can still need saving tips. How should we reduce our costs?

Know the different types of garage door springs

Ensure that the springs are replaced before starting. There are two types of these springs: extension springs and torsion springs.

Extension springs are long, coiled metal bands that provide a constant pull on the door until they reach their full length. They operate by converting the linear motion of being pulled to rotational motion, which tightens them around a shaft called an “eyelet”. The coils in extension springs are made from steel, but some companies use stainless steel or other metal alloys to improve performance and durability. Extension springs can be used for residential and commercial applications, but they have more limitations than torsion springs regarding weight-bearing and load-bearing capacity.

Torsion Springs work by twisting rather than stretching as extension springs do. They use torque (rotational force) instead of tension (linear force). Torsion Springs are more expensive to manufacture but have a longer lifetime and can be made thinner than extension springs. Torsion Springs are used in many applications, such as vehicle suspensions, airbags, shock absorbers for heavy-duty trucks and other industrial equipment, automobile bumpers, and various machine components.

At What Point Should You Start Using a Commercial Grade Spring?

A commercial-grade spring is a type of spring used in commercial applications. These springs are usually made from stainless steel, and they are designed to be able to withstand the additional pressure that is put on them in commercial use.

Commercial-grade springs are designed for use in a variety of different applications. They can be used for anything from doorstops to window shades. They can also be used for many other purposes, and they may vary depending on the brand and the design of the particular spring.


Replacing garage door springs can add up in terms of costs, but by having a garage door springs replacement cost guide from Elite Garage Doors, you can be sure to minimize the amount of money spent on repairs. Our 2024 guide provides accurate estimates for garage door torsion spring prices and coil spring replacement costs so that you can easily compare pricing and prepare your budget accordingly. Elite Garage Doors’ 2024 garage door spring replacement guide offers competitive prices on all kinds of garage door spring replacements while providing expert advice on how to safely and properly replace garage door coils, torsion springs, and more. Don’t get stuck trying to figure out how much replacing garage doors might cost – trust our 2024 garage door springs replacement cost as your go-to guide. Take the guesswork out of garage repair and let Elite Garage Doors show you the way